Profil Calon Promotor

# Tahun Penelitian
1 2020 Rekayasa Desain Multi-Hexagonal Crash Box Komposit Fiber Karbon Akibat Beban Frontal
Peran: Ketua Sumber Dana: Program Percepatan Profesor FTUB
2 2020 Simulasi Uji Tabrak pada Helm Sepeda Motor
Peran: Anggota Sumber Dana: Program BPPM FTUB
3 2019 Optimasi Desain Crash Box Multi-Hexagonal Akibat Frontal Load Model
Peran: Ketua Sumber Dana: Program Penelitian Doktor Lektor Kepala
4 2019 Karakteristik Pola Deformasi dan Penyerapan Energi Pada Honeycomb Filler Crash Box Akibat Frontal Load dan Oblique Load Test
Peran: Ketua Sumber Dana: Program Percepatan Profesor FTUB
5 2018 Studi Eksperimental Penyerapan Energi Dan Pola Deformasi Crash Box Pola Origami Pada Uji Qua-sistatic
Peran: Anggota Sumber Dana: Penelitian Kerja Sama Antar Perguruan Tinggi
6 2018 Optimasi Chassis Truk Mini Kapasitas 750 Kg Dengan Multi-Objective Response Surface Methods
Peran: Ketua Sumber Dana: Program Per-cepatan Profesor FTUB
7 2017 Pemodelan Coal Properties Terhadap Karakterisasi Pembakaran Pada Boiler Stoker
Peran: Ketua Sumber Dana: Program Per-cepatan Profesor FTUB
8 2017 Rekayasa Desain Komposit Fiber Karbon Untuk Pengembangan Chassis Monocoque Mobil
Peran: Anggota Sumber Dana: Penelitian Unggulan PT
9 2016 Multi-Objective Optimization Design Pada Crash Box Akibat Beban Arah Frontal
Peran: Ketua Sumber Dana: Program Per-cepatan Profesor FTUB
10 2015 Optimasi Desain Crash Box Multi Segmen untuk Peningkatan Performa Kemampuan Menyerap Energi Tabrak
Peran: Ketua Sumber Dana: Penelitian Unggulan PT
11 2013 Perancangan Metal Gasket Untuk Aplikasi Sealing Pada Tekanan Kerja Rendah
Peran: Ketua Sumber Dana: Penelitian Unggulan PT
# Tahun Publikasi
1 2020 Characteristics of Deformation Pat-tern and Energy Absorption in Hon-eycomb Filler Crash Box Due to Frontal Load and Oblique Load Test
Jurnal: Eastern-European Journal of Enterprise Technologies Vol. 2 No. 7/104
2 2020 Temperature Cycle Analysis of A6061-AISI304 Dissimilar Metal Continuous Drive Friction Welding
Jurnal: Eastern-European Journal of Enterprise Technologies Vol. 3 No. 12/105
3 2020 Analysis of multi-cell hexagonal crash box design with foam filled under frontal load model
Jurnal: Journal of Physics: Conference Series, vol. 1446
4 2020 The Effect of Adding Minerals on Plastic Aggregate to Lightweight Concrete
Jurnal: IOP Conference Series: Earth and Environmental Science, vol. 506
5 2020 Optimization of mini plantation tractor chassis by using multi-objective response surface methods
Jurnal: Journal of Physics: Conference Series, vol. 1446
6 2020 Energy Balance: Performing Energy Usefulness in AISI 304 Welding
Jurnal: Journal of Physics: Conference Series, vol. 1471
7 2020 Matching algorithm performance analysis for autocalibration method of stereo vision
Jurnal: Telkomnika (Telecommunication Computing Electronics and Control), vol. 18
8 2020 Computational fluid dynamics analysis of mini membrane module flow behavior
Jurnal: IOP Conference Series: Earth and Environmental Science, vol. 475
9 2020 Differences in precision of wax molds made of portland cement and silicone rubber in investment cast
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 845
10 2020 Characteristics of deformation pattern and energy absorption in honeycomb filler crash box due to fr
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 2
11 2020 Optimization of two segments crash box with rubber joint using response surface methodology
Jurnal: AIP Conference Proceedings, vol. 2278
12 2020 An Approach to Optimize the Corrugated Metal Gasket Design Using Taguchi Method
Jurnal: International Journal on Advanced Science, Engineering and Information Technology, vol. 10
13 2020 Parameter Optimization of ASSAB XW 42 Tool Steel on End Milling Process with MQCL Using Taguchi-WPCA
Jurnal: International Journal on Advanced Science, Engineering and Information Technology, vol. 10
14 2020 Analysis of the fracture area of tensile test for natural woven fiber composites (hibiscus tiliaceus-polyester)
Jurnal: Journal of Physics: Conference Series, vol. 1700
15 2020 The differences color intensity, PH, absorbance value of frangipani (Plumeria accuminata ait) sap during storage
Jurnal: Research Journal of Pharmacy and Technology, vol. 13
16 2019 Optimum design of laminated corrugated metal gasket using computer simulation
Jurnal: International Journal of Integrated Engineering Vol. 2 No. 5/98
17 2019 Sealing performance analysis of composite gaskets made of silicone rubber filled with ramie natural fibers
Jurnal: Journal of Mechanical Engineering and Sciences Vol. 13 No. 4
18 2019 Characterization of sodium-bicarbonate-treated zalacca fibers as composite reinforcements
Jurnal: Evergreen, vol. 6
19 2019 Movable blade vertical shaft kinetic turbine visual observation
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 2
20 2019 Evaluation of varied model order in GA-optimised parameter estimation of toothbrush rig system
Jurnal: International Journal of Integrated Engineering, vol. 11
21 2019 Energy absorption and deformation pattern on two segment crash box with rubber connection variation
Jurnal: Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, vol. 55
22 2019 Deformation Pattern and Energy Absorption Analysis on Initial Fold Crash Box by Oblique Crash Test
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
23 2019 Modified loop shaping algorithm in designing 2-DOF controller of a ladder-secondary double-sided lin
Jurnal: International Journal of Advanced Trends in Computer Science and Engineering, vol. 8
24 2019 Energy Absorption and Deformation Pattern on Two Segment Crash Box with Rubber Connection Varia-tion
Jurnal: Journal of Advanced Research in Fluid Mechanics and Ther-mal Sciences 55/ Issue 1
25 2019 Experiment on Novel Design of Tapered Shape Heat Pipe
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
26 2019 Vibration exposure of polydimethylsiloxane (PDMS) reinforced silica (sio 2 ): Comparison
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
27 2019 The Initial Modelling of Hybrid Plating for Internal Fixation Construct by Using 3-D Bone Model
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
28 2019 Effect of angle orientation lay-up on uniaxial tensile test specimen of Fiber carbon composite manuf
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
29 2019 Manufacture of Origami Pattern Crash Box Using Traditional Investment Casting Method
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 494
30 2019 Influence of several chemical treatment on the interfacial shear strength of zalacca fibres and low-
Jurnal: AIP Conference Proceedings, vol. 2097
31 2019 A Tensile Strength Analysis of Hibiscus cannabinus L. Fiber and Corn Silk Reinforced Polyester Resin
Jurnal: IOP Conference Series: Materials Science and Engineering, vol. 515
32 2019 Investigation of cogging forces using reluctance circuits equivalent approximation in a ladder secon
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 2
33 2019 Correlation of surface roughness, tool wear, and chip slenderness ratio in the lathe process of alum
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 4
34 2019 Sealing performance analysis of composite gaskets made of silicone rubber filled with ramie natural
Jurnal: Journal of Mechanical Engineering and Sciences, vol. 13
35 2018 Implementation of stereo vision semi-global block matching methods for distance measurement
Jurnal: Indonesian Journal of Electrical Engineering and Computer Science, vol. 12
36 2018 The effect of ladder-bar shape variation for a Ladder-Secondary Double-Sided Linear Induction Motor
Jurnal: Journal of Telecommunication, Electronic and Computer Engineering, vol. 10
37 2018 The modeling and optimization of hot rolling process of A36 structural steel by using response surfa
Jurnal: MATEC Web of Conferences, vol. 204
38 2018 Measurement Accuracy Analysis of Distance between Cameras in Stereo Vision
Jurnal: 2018 Electrical Power, Electronics, Communications, Controls and Informatics Seminar, EECCIS 2018, vol.
39 2018 Visualization of bubbles formation on the boiling process in tapering heat pipe with variation of ev
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 3
40 2018 The role of Carica papaya latex and aluminum oxide on the formation of carbon nanofibre made of coco
Jurnal: Advances in Natural Sciences: Nanoscience and Nanotechnology, vol. 9
41 2018 Heat treatment effect on metal matrix composite with brass matrix and fly ash
Jurnal: MATEC Web of Conferences, vol. 204
42 2018 Experimental and micromechanical modelling of randomly oriented zalacca fibre/low-density polyethyle
Jurnal: Cogent Engineering, vol. 5
43 2018 Study of Cogging Forces in A Ladder-secondary Double-sided Linear Induction Motor (DSLIM) for Asymme
Jurnal: 2018 Electrical Power, Electronics, Communications, Controls and Informatics Seminar, EECCIS 2018, vol.
44 2018 CFD modelling of particle size effect on stoker coal-fired boilers combustion
Jurnal: Eastern-European Journal of Enterprise Technologies 3(8-93)
45 2018 Symmetrical Optimum on 2DOF Cascaded-PI for A Position Control Using A Ladder-Secondary Double-Sided
Jurnal: 2018 2nd International Conference on Applied Electromagnetic Technology, AEMT 2018, vol.
46 2018 Configuration on hybrid plating to improve internal fixation on femur bone model
Jurnal: MM Science Journal
47 2018 Effect of evaporator-condenser diameter ratio (D/D) on thermal performance of the tapering heat pipe
Jurnal: Eastern-European Journal of Enterprise Technologies, vol. 5
48 2018 An overview of fracture mechanics with ANSYS
Jurnal: International Journal of Integrated Engineering 10(5)
49 2018 Flux Density Distribution and Cogging Action Using Reluctance Network Equivalent in Simple Magnetic
Jurnal: 2018 Electrical Power, Electronics, Communications, Controls and Informatics Seminar, EECCIS 2018, vol.
50 2017
Jurnal: Journal of Engineering Science and Technology, vol. 12
51 2017 Design, manufacture and finite element analysis of a small-scale ladder-secondary double-sided linea
Jurnal: Advanced Science Letters, vol. 23
52 2017 A vertical axis hinged blade kinetic turbine performance using response surface methodology
Jurnal: Journal of Engineering Science and Technology, vol. 12
53 2017 AISI 304 welding fracture resistance by a charpy impact test with a high speed sampling rate
Jurnal: Metals, vol. 7
54 2017 Surface roughness and roundness optimization on turning process of aluminium alloy with Taguchi meth
Jurnal: Journal of Mechanical Engineering, vol. 14
55 2016 Effect of alkaline treatment on the characterization of zalacca midrib wastes fibers
Jurnal: AIP Conference Proceedings, vol. 1717
56 2016 The effect of hold time of overload on crack propagation behavior emerging from notch root
Jurnal: FME Transactions, vol. 44
57 2016 Crash energy absorption of two-segment crash box with holes under frontal load
Jurnal: AIP Conference Proceedings, vol. 1717
58 2016 Mechanical properties of untreated and alkaline treated fibers from zalacca midrib wastes
Jurnal: AIP Conference Proceedings, vol. 1717
59 2016 Electrochemical corrosion of as-cast and annealed Zr48Cu36Al8Ag Jurnal: Materials Science Forum, vol. 863
60 2016 Crash energy absorption of multi-segments crash box under frontal load
Jurnal: Jurnal Teknologi (Sciences & Engineering), Vol. 78 No. 5
61 2016 Simulation of two segments crash box subjected to frontal load
Jurnal: ARPN Journal of Engineering and Applied Sciences Vol. 11, No. 2
62 2015 Anouter movable blade vertical shaft kinetic turbine performance
Jurnal: International Journal of Applied Engineering Research, vol. 10
63 2015 Bowl bladed vertical shaft kinetic turbine performance using response surface methodology (RSM)
Jurnal: International Journal of Applied Engineering Research, vol. 10
64 2014 Architectural System Design of Six Channels Compact Fuzzy Logic Controller for Arm Robot Joints Usin
Jurnal: Applied Mechanics and Materials, vol. 541-542
65 2014 Optimization spring coil design for orthodontic tooth movement
Jurnal: Applied Mechanics and Materials, vol. 493
66 2014 Optimum Shape and Dies Design for New Thin Metal Gasket by Using Simulation Experiment
Jurnal: Applied Mechanics and Materials Vol. 575
67 2013 Influence of surface roughness on leakage of new metal gasket
Jurnal: International Journal of Pressure Vessels and Piping 111-112